Plumbing Basics: Before Bathtub Installation
SourceThey are making a few good pointers on the subject of How to Install a Bathtub overall in this post followed below.
Mounting a bathtub isn't exactly brain surgery, but it does require strong plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old bathtub with a new one is also a reasonably difficult task. If the old tub is readily available, the job can move quickly; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will need a helper to vacate the old bathtub and also set in the brand-new one. Make sure you have certified yourself for the work and are comfortable attempting it. As opposed to working with a service provider to take over a halfway-completed job, it is far better to take into consideration employing one before you start. Possibilities are you might require an expert plumber to make tube links.
This post will certainly assist you mount a brand-new bathtub in your restroom if you have already acquired a new tub as well as do not require to change the plan of your previous water supply pipelines.
Your devices and product list ought to make up the following:
Getting ready for the Installment
To start with, the supporting frame provided with the bathroom should be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to avoid pressure on the tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its final setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of removing the existing taps can be fairly bothersome as a result of the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a fabric ready for the remaining water that will certainly come from the pipes. When the supply pipelines have been removed, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bath tub
Using the two wood boards under its feet, place the tub in the required setting. The wood boards are useful in uniformly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small factors.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bathtub till the level reads degree.
To set up faucets, fit all-time low of the furthest adaptable tap adapter to the proper supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Switch on the water supply as well as examine all joints and new pipework for leakages and also tighten them if required. Fill up the bath tub and also inspect the overflow electrical outlet and the regular outlet for leakages.
Lastly, repair the bath paneling as defined in the producer's user's manual. Tiling as well as sealing around the tub needs to wait till the bath tub has actually been made use of at the very least once as this will resolve it right into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making sure that the washers are in area between the tap as well as the sink. Safeguard the tap in place with the maker provided backnut. Once the tap is safely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former kind should be linked to the faucet ends initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to crack an inflexible seal, triggering the water to penetrate the wall surface between the bath and also the tiling, causing problems with wetness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and also cartridges, and are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of soaked paper or soft rope. Remember to always fill up the tub with water before securing, to permit the activity experienced when the tub remains in use. The sealer can crack rather early if you do not consider this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very interested in Installing A Bathtub and I am assuming you enjoyed our page. Enjoyed reading our write-up? Please share it. Help someone else locate it. I treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Rely on our service.